B4100528 / 00
April 2005
MFCD 1219
User Manual
SAFETY INSTRUCTIONS
• Read the safety and
in a residential area is likely
to cause harmful
interference in which case
the user will be required to
correct the interference at
his own expense.
upon or pinched by items
placeduponoragainstthem,
payingparticularattentionto
cords at plugs and
receptacles.
operatinginstructionsbefore
operating the apparatus.
•Retainsafetyandoperating
instructions for future
reference.
Water and moisture
• Adhere to all warnings on
the apparatus and in the
•
Never expose the
•
This Class
B
digital
apparatustorainormoisture.
• Never use the apparatus
near water - e.g. near a
operating
manual.
• Follow all instructions for
operation and use.
instructions
apparatus complies with
Canadian ICES-003.
Cet appareil numérique de
la classe B est conforme à la
normeNMB-003duCanada.
bathtub,
washbasin,
swimmingpool,kitchensink,
laundry tub or in a wet
basement.
•Thisapparatusconformsto:
UL60950,
cUL60950,
IEC60950, CE
Power connection
Ventilation
• Do not cover or block the
ventilation openings in the
cover of the set. When
installing the apparatus in a
cupboard or another closed
location,heedthenecessary
space between the set and
the sides of the cupboard.
• Warning: This apparatus
must be earthed!
• FCC notice
This equipment has been
tested and found to comply
with the limits of a class B
digital device, pursuant to
Part 15 of the FCC rules.
These limits are designed to
•
Power requirements:
connect the apparatus to an
AC voltage as indicated at
its back. Using a lower
voltage, the apparatus will
notbeabletooperate.Using
provide
reasonable
a
higher voltage may
Installation
protection against harmful
interference when the
equipment is operated in a
commercial environment.
This equipment generates,
uses and can radiate radio
frequency energy and, if not
installed and used in
accordance with the
instruction manual, may
cause harmful interference
to radio communications.
Operation of this equipment
damage the apparatus.
Ifyouarenotsureofthetype
of power supplied, consult
the power company.
•Donotoverloadwalloutlets
and extension cords as this
may result in fire or electric
shock.
•Mainsleadprotection(U.S.:
Power cord): Supply cords
shouldberoutedsothatthey
are not likely to be walked
• Place the apparatus on a
flat, solid and stable surface
thatcanbeartheweightofat
least 3 monitors. If you use
an unstable cart or stand,
the set may fall, causing
serious injury to a child or
adult, and serious damage
to the equipment.
© 2005 BARCO nv. Allrights reserved.
CONTENTS
1. Overview ..................................................................................................... 5
1.1 Introduction ......................................................................................... 5
1.2 Package contents................................................................................ 6
1.3 Controls and connectors ..................................................................... 6
2. Installation ................................................................................................... 8
2.1 Precautions ......................................................................................... 8
2.2 Wall mounting ..................................................................................... 8
2.3 Connecting the signals...................................................................... 10
2.4 Starting up ......................................................................................... 11
2.5 Install the DICOM Optimizer software ............................................... 11
3. On-screen display (OSD) menus ............................................................ 12
3.1 How to use the OSD.......................................................................... 12
3.2 Description of the menu items .......................................................... 13
Main menu ......................................................................................... 13
Video menu ....................................................................................... 14
Color Menu ........................................................................................ 15
Clock Menu ........................................................................................ 15
4. Maintenance ............................................................................................. 16
Appendix A: Possible resolutions.................................................................. 17
Appendix B: Technical specifications ............................................................ 18
MFCD 1219 User's Guide
4
1. OVERVIEW
1.1 Introduction
The MFCD 1219, BARCO’s full color 19” LCD
display, guarantees perfect image quality in
medical imaging applications.
The display combines a TFT (thin film transistor)
liquid crystal display panel structure and a built-in
backlight with inverter for a better picture quality.
It is designed to meet users' needs for
performance, consistency, and outstanding image
quality through a streamlined development
process in which wall-mount functionality
provides a variety of capability.
The image on the display can be adjusted by
means of the extended on-screen menu system
(OSD).
The internal memory can contain settings for 24
different types of video signals (with different
timings). 22 are factory-preset, 2 are user-
definable.
The display accepts the most common display
standards. However, it is limited to the following
specifications:
Multi-scan capabilities
Analog video:
The horizontal frequency must be between 31
and 91 kHz, the vertical frequency between 56
and 85 Hz.
Digital video:
The horizontal frequency must be between 31.47
and 64 kHz, the vertical frequency between 60
and 70 Hz.
The optimum and recommended resolution is
1280 x 1024 / 60 Hz.
MFCD 1219 User's Guide
5
The monitor comes with a power saving feature;
therefore, you may put the monitor into a power
saving state when it is not in use. This feature
complies with both EPA‘s Energy Star
Power Saving
requirements and European NUTEK/TCO’s
power management guidelines. It conforms to
Video Electronics Standard Association (VESA)
approved DPMS power-down signaling method.
This monitor automatically cuts down power
consumption of monitor set when not detecting
Hsync or Vsync signals. This feature is compliant
with VESA DPMS.
1.2 Package contents
The package should include the following items,
please check. If some of the items are missing,
please contact the reseller you have purchased
the unit from.
-
-
-
-
-
-
-
-
-
The display with foot
12V DC adapter
European power cord
American power cord
UK power cord
Video cables: VGA cable and DVI-D cable
Mounting plate with 4 screws
This user manual
NioWatch CD-ROM
MFCD 1219 User's Guide
6
1.3 Controls and connectors
(9)
(1)
(2)
(3)
(4)
(5)
(6) (7)
(8)
(1) 12V DC power input
(2) Analog video input
(3) DVI input (DVI-D supported only)
(4) Menu key
(5) <-> Key
(6) <+> Key
(7) Power LED
The LED is off when the display is off.
The LED is green when the display is on.
The LED is orange when the display is in
power-saving mode (stand-by)
(8) Power key
(9) Push-button to release the panel from the
foot
MFCD 1219 User's Guide
7
2. INSTALLATION
2.1 Precautions
•
Keep your original packaging. It is
designed for this display and is the ideal
protection during transport.
•
•
•
Avoid reflections in the flat panel to reduce
eye strain.
Place the display on a strong and stable
table or desk.
Keep the display away from heat sources
and provide enough ventilation in case it is
built in a rack or console.
•
Make sure computer and display are
switched off before connecting the signals.
2.2 Wall mounting
You can mount the panel to the wall instead of to
the foot, by means of the supplied mounting
plate. If you do not need to mount the panel to the
wall, please skip this item.
Step 1: Remove the panel from the foot
1
Position one hand under the panel at the
front side. Position the other hand at the
rear, under the push-button with BARCO
logo (9).
2
3
Firmly press down the push-button (9) with
one hand while carefully lifting the panel up
with the other hand.
Remove the panel from the foot.
Step 2: Fix the mounting plate to the wall
1
Screw the mounting plate to the wall with
the 4 supplied screws (A).
MFCD 1219 User's Guide
8
A
2
Slide back the locks at both sides of the
mounting plate (B). In that way, you can
secure the panel to the mounting plate after
placing the panel.
B
Step 3: Place the panel on the mounting
plate
1
Place the panel on the mounting plate (C). If
you want to secure the panel to the
mounting plate, place the
panel in the frontmost
notches.
Please make sure that the
four shafts are securely
placed in the notches of the
mounting plate.
C
MFCD 1219 User's Guide
9
2
To secure the panel, slide forward the
locks on both sides of the mounting plate.
Lock the panel with one screw at both
sides (D).
D
2.3 Connecting the signals
To connect the video & sync signals:
1
Connect one end of the appropriate video
cable to the corresponding video input of
the monitor.
Analog video: Connect to input (2)
DVI: Connect to input (3)
2
Connect the other end of the video cable to
the video output of your video source.
Analog video: Computer graphics board
with analog video output
DVI: Computer graphics board with digital
video output
(1)
(2)
(3)
To connect the power:
1
2
3
Connect one end of the proper power cable
to the AC input of the 12V DC adapter.
Connect the 12V supply of the 12V DC
adapter to the DC input (1) of the monitor.
Connect the other end of the power cord to
a grounded power outlet.
MFCD 1219 User's Guide
10
2.4 Starting up
Proceed as follows:
1
2
Switch on the computer.
Switch on the display by pushing the Power
key (8).
3
If necessary, select a suitable resolution in
the computer operating system. Please
refer to Appendix A, "Possible resolutions"
in the back of this manual.
Note: The recommended resolution for best
image quality is 1280x1024 at 60 Hz.
The microcontroller in the display checks if the
connected video signal has been adjusted before,
and if these adjustments have been stored in the
memory. There are 2 possibilities:
(8)
a) The video signal has been adjusted and
stored in the memory.
In this case, the display switches to this memory
location (the so-called mode) and the image will
need no further adjustments.
b) The video signal has not been adjusted and
stored yet.
In this case, the display will auto-size the picture
and store the settings in one of the user modes.
2.5 Install the NioWatch software
Proceed as follows:
Insert the CD-ROM in the CD-ROM drive. The
CD-ROM starts automatically. Please follow the
instructions on the screen.
The CD-ROM contains user instructions about the
usage of the NioWatch.
MFCD 1219 User's Guide
11
3. ON-SCREEN DISPLAY (OSD)
MENUS
3.1 How to use the OSD
Proceed as follows:
1
Press the Menu key (4) on the front to display
the OSD main menu.
Note:
It may be possible that the OSD menu does
not appear. If this is the case, the front
Controls are locked. To unlock them, please
follow the procedure described in § 3.2 below.
2
3
Press the <+> key (6) or <-> key (5) to scroll to
the desired menu item.
Press the Menu key (4) to activate the
selected function or to enter the selected
secondary menu.
(5)
(4)
(6)
4
If you have activated a function:
a)Press the <+> key (6) or <-> key (5) to
change the value.
b)Press the Menu key (4) to enter the new
value and return to the menu.
To exit the OSD while saving the changes,
select Save & Exit.
5
To exit the OSD without saving the changes,
select Cancel.
Main Menu
Note: The OSD disappears
- (Down)
+ (Up)
automatically after an
inactivity period of 30
seconds.
Highlighted bar
Brightness
35
50
Contrast
Auto Adjust
H Position
V Position
Color
75
29
>
The color of the highlight bar
indicates the status of the mode.
Clock
>
RED indicates the function is
selected and ready to be
adjusted.
Languages
Input Type
>
>
Lock Controls
Cancel
Blinking RED indicates OSD is in
parameter adjusting mode.
Save & Exit
Input type
A1
1024 x 768 - 60.1
Resolution
48.4k
MFCD 1219 User's Guide
12
3.2 Description of the menu items
Main menu
Function
Description
Brightness
To adjust the overall image and
background brightness level.
Contrast
To adjust the image brightness in
relation to the background
(the background is unchanged).
Auto Adjust *
To automatically set the H Position,
V Position and Clock.
Horizontal Position To move the screen horizontally
left or right.
Vertical Position
Color
To move the screen vertically
upward or downward.
To adjust parameters for the screen
colors of Red, Green and Blue.
Clock
To adjust the function only when
characteristics are blurred.
Languages
To select English, French, Italian,
German or Spanish for OSD
language.
Input Type
To select Analog (A1) or
DVI-Digital (D) input source.
Lock Controls **
When locked, the OSD menu will not
appear when pressing the Menu key.
Cancel
To restore the previous setting.
Save & Exit
To save the adjustments and quit the
OSD menu.
*Auto Adjust function will be automatically
executed whenever the system is switched to a
new mode. When the system is changed to this
mode again later on, the system will not repeat the
Auto Adjust function. This function is only valid
when the mode concerned is selected for the first
time.
MFCD 1219 User's Guide
13
**To unlock the Controls, proceed as follows:
1
2
Press the Power key to switch off the display
With one hand, press and hold the <+> and
the <-> key at the same time.
With the other hand, press the Power key
shortly to switch the display on again.
3
4
Keep holding the <+> and the <-> key for
about 3 seconds.
At last, release the <+> and the <-> key.
Now, by pressing the Menu key, the OSD
menu will appear.
Note:
The bottom line of the OSD shows the input type,
current resolution of the monitor and status of
vertical sync. If it shows user mode, one of the
user modes is selected.
Color Menu
Color Menu
Function
Description
- (Down)
Auto Balance
+ (Up)
Auto Balance
To automatically adjust the contrast
level of RGB. This does not support
resolution of Mac 832 x 624 at 75Hz.
68
65
70
>
Red
Green
Blue
Main Menu
A1 1024 x 768 - 60.1 48.4k
R
To adjust the level of color Red.
To adjust the level of color Green.
To adjust the level of color Blue.
To return to Main Menu.
G
B
Main Menu
MFCD 1219 User's Guide
14
To perform the Autobalance function, you need
to select a proper test pattern before performing
the function.
Proceed as follows:
1
You must have installed the Barco
NioWatch software.
2
3
Right-click on the NioWatch systray icon.
Select Test Patterns from the pop-up
menu.
4
5
Select the SMPTE test pattern.
Now perform the function Autobalance
from the MFCD 1219 control panel.
6
When finished, click on the test pattern to
close it.
Clock Menu
Function
Description
Clock Menu
- (Down)
OSD Position
Clock
+ (Up)
OSD Position To display the OSD to your preferred
position.
1344
4
>
Clock Phase
Main Menu
A1 1024 x 768 - 60.1 48.4k
Clock
To adjust the function only when
characteristics are blurred.
Clock Phase
Main Menu
To adjust ADC sampling clock phase.
To return to Main Menu.
MFCD 1219 User's Guide
15
4. MAINTENANCE
Panel
Take care not to damage or scratch the panel.
Clean with a soft woolen or cotton towel. Use a
watery solution or a mild commercial glass
cleaning solution.
Cabinet
Do not use chemical cleaning products, benzene,
toluene, xylene or other solvents.
Clean with a soft cloth dampened with mild
detergent and water. Repeat this with water only
and wipe dry with a dry cloth.
MFCD 1219 User's Guide
16
APPENDIX A: POSSIBLE
RESOLUTIONS
There are 22 preset modes and 2 user modes.
The following modes are preset as factory
defaults.
Resolution
Pixel
Horizontal Vertical
Standard
Analog Digital
Freq. (MHz) Freq. (kHz) Freq. (Hz)
640 x 350
640 x 480
25.175
25.175
30.24
31.50
31.50
36.00
28.321
36.00
40.00
50.00
49.50
56.25
57.29
65.00
75.00
78.80
80
31.47
31.47
35.00
37.90
37.50
43.30
31.47
35.10
37.88
48.10
46.88
53.70
49.80
48.36
56.50
60.02
60.24
68.70
67.50
63.98
80
70
60
67
72
75
83
70
56
60
72
75
85
74.6
60
70
75
75
85
75
60
75
85
VGA
VGA/VESA
Mac
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
VESA
VESA
VESA
VGA
720 x 400
800 x 600
V
V
VESA
VESA
VESA
VESA
VESA
Mac
832 x 624
1024 x 768
VESA
VESA
VESA/CRUS
Mac
V
94.50
108
VESA
VESA
VESA
VESA
VESA
1152 x 864
1280 x 1024
108
V
135
157.5
91.146
MFCD 1219 User's Guide
17
APPENDIX B: TECHNICAL
SPECIFICATIONS
Max. video input bandwidth
Picture panel
157.5 MHz
19-inch diagonal viewable screen
TFT (thin film transistor) active matrix,
color liquid crystal display, RGB
interface
Signal system
Analog RGB signals, DVI digital
Front panel controls
Resolution
Menu, - (down / decrease), + (up /
increase), Power
1280 x 1024 (native)
Display area (H x V)
Input connectors
376 x 301 (mm)
15-pin D-sub
(for PC graphic signal input)
3P - Mini – DIN – Power –Connector
(for DC 12V, 6.5A input)
Pixel Pitch
0.294 mm (H) x 0.294 mm (V)
DVI connector (supporting DVI-D only)
Display color
16M
Power source
100 ~ 240 VAC
Luminance
250 cd/m2 (typ.)
Power consumption
50 W (max.)
Contrast ratio
500:1 (typ.)
Less than 5 W in power-off mode
Response time
Power saving
25 ms (Tr+Td) typ. total
VESA DPMS standard
EPA/Energy Star compliant
Viewing angle
Vertical: 176º (typ.)
Horizontal: 176º (typ.)
PnP compatibility
VESA DDC 2B standards compliant
Input signals
Analog: Hor. 31.47 to 91.2 kHz
Vert. 56 to 85 Hz
Safety standards
UL60950, cUL60950, IEC60950, CE
Sync types: Separate sync,
composite sync, sync on
Green
Dimensions (W x H x D)
450 mm x 461.8 mm x 213.9 mm
Digital: Hor. 31.47 to 64 kHz
Vert. 60 to 70 Hz
MFCD 1219 User's Guide
18
CONTINUOUS PRODUCT
Net weight
7.7 kg
IMPROVEMENT, THE ABOVE
SPECIFICATIONS ARE SUBJECTED
TO CHANGE WITHOUT NOTICE.
BARCO SHALL NOT BE LIABLE
FOR TECHNICAL OR EDITORIAL
ERRORS OR OMISSIONS
Operating Temperature
0°C to 40°C
Storage Temperature
-20°C to 60°C
CONTAINED HEREIN; NOR FOR
INCIDENTAL OR CONSEQUENTIAL
DAMAGES WHATSOEVER
NOTICE:
DUE TO OUR POLICY OF
RESULTING FROM FURNISHING,
PERFORMANCE OR USE OF THIS
MATERIAL.
MFCD 1219 User's Guide
19
|