Owner’s manual
Mode d’emploi
1. PRECAUTIONS
1. When the inside of the car is very cold and
the player is used soon after switching on
the heater, moisture may form on the disc
or the optical parts of the player and proper
playback may not be possible. If moisture
forms on the disc, wipe it off with a soft
cloth. If moisture forms on the optical parts
of the player, do not use the player for about
one hour and the condensation will disap-
pear naturally to allow normal operation.
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reason-
able protection against harmful interference in
a residential installation. This equipment gen-
erates, uses, and can radiate radio frequency
energy and, if not installed and used in accor-
dance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interfer-
ence will not occur in a particular installation. If
this equipment does cause harmful interfer-
ence to radio or television reception, which can
be determined by turning the equipment off
and on, the user is encouraged to consult the
dealer or an experienced radio/TV technician
for help.
Manual de instrucciones
■ Contents
English
2. Driving on extremely bumpy roads which
cause severe vibration may cause the
sound to skip.
1. PRECAUTIONS...........................................................2
2. CONTROLS.................................................................3
3. BUTTON TERMINOLOGY..........................................4
4. FEATURES..................................................................5
5. HANDLING COMPACT DISCS...................................6
6. DCP (Detachable Control Panel)..............................7
7. REMOTE CONTROLL ................................................8
8. OPERATION..............................................................10
9. TROUBLESHOOTING ..............................................14
10.ERROR DISPLAYS...................................................15
11.SPECIFICATIONS.....................................................16
3. This unit uses
a
precision mechanism.
Even in the event that trouble arises, never
open the case, disassemble the unit, or
lubricate the rotating parts.
■ Table des matières
CAUTION
Français
BD316
USE OF CONTROLS, ADJUSTMENTS, OR PERFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN, MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
THE COMPACT DISC PLAYER SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE
EXCEPT PROPERLY QUALIFIED SERVICE PERSONNEL.
1. PRÉCAUTIONS.........................................................17
2. COMMANDES.............................................................3
3. NOMENCLATURE DES TOUCHES .........................18
4. CARACTÉRISTIQUES..............................................19
5. MANIPULATION DES DISQUES COMPACTS ........20
6. CLAVIER DE COMMANDE AMOVIBLE (DCP) .......21
7. TÉLÉCOMMANDE....................................................22
8. FONCTIONNEMENT.................................................24
9. DÉPISTAGE DES PANNES......................................28
10.AFFICHAGE DES ERREURS...................................29
11.SPÉCIFICATIONS.....................................................30
AM/FM CD PLAYER
•
RADIO AM/FM-LECTEUR CD
•
RADIO AM/FM Y REPRODUCTOR CD
MODEL
DX57
12V
GROUND
AM 530-1710kHz/FM 87.9-107.9MHz
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED
OPERATION.
■ Índice
Español
THIS PRODUCTION COMPLIES WITH DHHS RULES 21 CFR
1. PRECAUCIONES......................................................31
2. CONTROLES..............................................................3
3. NOMENCLATURA DE LOS BOTONES...................32
4. CARACTERÍSTICAS ................................................33
5. MANEJO DE LOS DISCOS COMPACTOS..............34
6. PANEL DE CONTROL DESMONTABLE (DCP) ......35
7. CONTROLADOR REMOTO.........................................36
8. OPERACIÓN.............................................................38
9. SOLUCIÓN DE PROBLEMAS..................................42
10.INDICACIONES DE ERROR ....................................43
11.ESPECIFICACIONES ...............................................44
SUBCHAPTER
J
APPLICABLE AT DATE OF MANUFACTURE.
CLARION CO.,LTD.
50 KAMITODA,TODA-SHI,SAITAMA-KEN,JAPAN
Bottom View of Source Unit
MANUFACTURED:
286- 324-00
Clarion Co.,Ltd.
MADE IN CHINA
SERIAL No.
PE-2310B
INFORMATION FOR USERS:
CHANGES OR MODIFICATIONS TO THIS PRODUCT WILL VOID THE WARRANTY AND WILL
VIOLATE FCC APPROVAL.
Clarion Co., Ltd.
All Rights Reserved. Copyright © 2001: Clarion Co., Ltd.
Printed in China / Imprimé en Chine / Impreso en China
Be sure to unfold and read the next page.
Veuillez déployer et vous référer à la page suivante.
Cerciórese de desplegar y de leer la página siguiente.
PE-2394B
280-7619-00
•
2000/1 (D C)
BD316
2
4. FEATURES
■ Rotary Encoder Volume Control
■ DIN Chassis with Detachable Control Panel
■ Z-Enhancer with 3 Mode Sound Selector
■
® FM Reception System
■ AM/FM Bands-1 AM, 3 FM/18 FM/6 AM Touchbutton Memory
■ 8-Times Oversampling Digital Filter and Dual 1-Bit D/A Converters
■ Zero-Bit Detector Mute Circuit
■ Repeat/Random Play/Intro Music Scan
■ Multi-Color LC Display
■ 4-Channel RCA Line Level Output with Fader Control
■ 180 W (45 W × 4) Maximum Power Output
■ Infrared Remote Control
BD316
5
5. HANDLING COMPACT DISCS
This unit has been designed specifically for play-
Note on Compact Discs
Never stick labels on the surface of the compact
disc or mark the surface with a pencil or pen.
back of compact discs bearing the
No other discs can be played.
mark.
To remove the compact disc from its storage
case, press down on the center of the case and
lift the disc out, holding it carefully by the edges.
No
Proper way to hold
the compact disc
Removing the disc
Do not use any solvents such as commercially
available cleaners, anti-static spray, or thinner to
clean compact discs.
Always handle the compact disc by the edges.
Never touch the surface.
No
To remove fingermarks and dust, use a soft
cloth, and wipe in a straight line from the center
of the compact disc to the circumference.
No
Do not use compact discs that have large
scratches, are misshapen, or cracked, etc. Use
of such discs will cause misoperation or damage.
No
New discs may have some roughness around
the edges. The unit may not work or the sound
may skip if such discs are used. Use a ball-point
pen, etc. to remove roughness from the edge of
the disc.
Ball-point pen
Roughness
Do not expose compact discs to direct sunlight
or any heat source.
No
Note:
Do not use commercially available CD protection sheets or discs equipped with stabilizers, etc. These
•
may get caught in the internal mechanism and damage the disc.
6
BD316
6. DCP (Detachable Control Panel)
The control panel can be detached to prevent
theft. When detaching the control panel, store it
in the included DCP case to prevent scratches.
We recommend taking the detachable control
CAUTION
• The DCP can easily be damaged by shocks. After
removing it, place it in a protective case and be
careful not to drop it or subject it to strong shocks.
panel with you when leaving the car.
When the release button is pressed and the DCP is
unlocked, the car’s vibrations may cause it to fall.
To prevent damage to the DCP, always store it in a
protective case after detaching it.
•
•
Removing the DCP
1. Turn off the power.
The rear connector that connects the source unit
and the DCP is an extremely important part. Be
careful not to damage it by pressing on it with fin-
gernails, pens, screwdrivers, etc.
2. Press the DCP Release button 1.
DCP Release button 1
DCP Rear Panel
Source Unit Front
DCP
connector
Source unit connector
The DCP is unlocked.
*
3. Remove the DCP.
Note:
If the DCP is dirty, wipe off with a soft, dry cloth only.
•
Attaching the DCP
Insert the DCP into the right side of the source
unit and press the left side to lock it.
CAUTION
Do not insert the DCP from the left side. Doing so
may damage it.
2.
DCP
1.
Storing the DCP in the DCP Case
Hold the DCP, in the orientation as shown in the
figure below, and put it into the supplied DCP
case. (Ensure the DCP is in the correct orienta-
tion.)
DCP
DCP case
BD316
7
7. REMOTE CONTROL
Receiver for remote control unit
Operating range: 30° in all directions
Remote Control Unit
Signal transmitter
¥
*
)
(
&
™
¡
£
§
¢
∞
Inserting the Batteries
1. Turn the remote control unit over, then slide
the rear cover in the direction of the arrow.
AA (UM-3/1.5 V)
Batteries
2. Insert the AA (UM-3/1.5 V) batteries that
came with the remote control unit facing in
the directions shown in the figure, then close
the rear cover.
Notes:
Using batteries improperly can cause them to explode.
Take note of the following points:
Rear cover
• When replacing batteries, replace both batteries with
new ones.
Rear side
• Do not short-circuit, disassemble or heat batteries.
• Do not dispose of batteries into fire or flames.
• Dispose of spent batteries properly.
8
BD316
Functions of Remote Control Unit Buttons
Mode
Radio
CD
Button
¥ FUNC
Turns power on and off. When pressed and held for 1 second: Turns power off.
Switches between radio and CD.
& BAND
Switches reception band.
Plays the first track.
Top play.
DISC UP
PROG
TOP
* VOLUME
Increases and decreases volume (in all modes).
Moves preset channels up and down. Moves tracks up and down.
( SEARCH
When pressed and held for 1 second:
Fast-forward/fast-backward.
) PLAY/PAUSE Turns mute on and off.
Switches between playback and pause.
Switches between playback and pause.
¡ MUTE
Turns mute on and off.
™ ISR
Recalls ISR radio station in memory.
Press and hold for more than 2 seconds: Stores current station into ISR memory
(radio mode only).
£ DISP
Switches among main display, sub display and clock display.
¢ SCAN
Preset scan.
When pressed and held for 2 seconds:
Auto store.
Scan play.
PS/AS
∞ RPT
No function.
Repeat play.
BLS
§ RDM
No function.
Random play.
MONI
* Some of the corresponding buttons on the source unit and remote control unit have different functions.
BD316
9
8. OPERATION
Note:
Be sure to read this chapter referring to the front diagrams of chapter 2. CONTROLS on page 3 (unfold).
•
Adjusting the Treble
Basic Operations
1) Press A-M button 2 and select “TREB”.
CAUTION
2) Turning the Rotary knob $ clockwise empha-
sizes the treble; turning it counterclockwise
attenuates the treble.
When this unit is turned on, starting and stop-
ping the engine of a car with its volume raised
to the maximum level may harm your hearing.
Be careful about adjusting the volume.
The factory default setting is “0”. (Adjustment
range: –6 to +6)
*
3) When the adjustment is complete, press A-M
button 2 several times until the function
mode is reached.
Turning ON the Power and Adjusting
the Volume
1) Press the POWER button 3.
To turn off the power, press the POWER button
3 for 1 second or longer.
*
Adjusting the Balance
1) Press A-M button 2 and select “BAL”.
2) Press the FNC button 3 and select another
operation mode. Every time the FNC button
3 is pressed, the display changes the oper-
ation mode as:
2) Turning the Rotary knob $ clockwise empha-
sizes the sound from the right speaker; turn-
ing it counterclockwise emphasizes the sound
from the left speaker.
Radio ➜ CD ➜ Radio
The factory default setting is “0”. (Adjustment
range: L9 to R9)
*
Notes:
The operation mode not connected to the unit will not
be selected.
•
3) When the adjustment is complete, press A-M
button 2 several times until the function
mode is reached.
If the CD mode is selected when no disc is inserted,
the display flashes “ NO DISC”.
•
3) Turning the Rotary knob
$
clockwise
Adjusting the Fader
increases the volume; turning it counterclock-
wise decreases the volume.
1) Press A-M button 2 and select “FAD”.
The volume level is from 0 (minimum) to 33 (max-
imum).
*
2) Turning the Rotary knob $ clockwise empha-
sizes the sound from the front speakers; turn-
ing it counterclockwise emphasizes the sound
from the rear speakers.
Audio Mode Adjustments
The factory default setting is “0”. (Adjustment
range: F9 to R9)
Press the A-M button 2 to select the adjustment
mode. The mode switches as follows each time
the A-M button is pressed:
BASS ➜ TREB ➜ BAL ➜ FAD ➜ Previous
mode
*
3) When the adjustment is complete, press A-M
button 2 several times until the function
mode is reached.
Adjusting the Bass
1) Press A-M button 2 and select “BASS”.
2) Turning the Rotary knob $ clockwise empha-
sizes the bass; turning it counterclockwise
attenuates the bass.
The factory default setting is “0”. (Adjustment
range: –6 to +6)
*
3) When the adjustment is complete, press A-M
button 2 several times until the function
mode is reached.
10
BD316
Setting the Z-enhancer
This unit comes with three types of sound tone
effects stored in memory. Select the one you prefer.
Radio Mode Operations
FM Reception
For enhanced FM performance the
tuner includes signal actuated stereo control and
Multipath noise reduction circuits.
The factory default setting is “Z-EHCR OFF”.
*
®
Each time you press Z-EHCR button !, the
tone effect changes in the following order.
“Z-ENHANCER 1” ➜ “Z-ENHANCER 2” ➜
“Z-ENHANCER 3” ➜ “Z-EHCR OFF” ➜
“Z-ENHANCER 1”...
Listening to the Radio
• Z-ENHANCER 1: bass emphasized
• Z-ENHANCER 2: treble emphasized
• Z-ENHANCER 3: bass and treble emphasized
• Z-EHCR OFF: no sound effect
1) Press the FNC button 3 to select the radio
mode, then the radio will be on.
2) To select a preset band, press the BND but-
ton @, then select one of the preset bands
such as FM1, FM2, FM3, or AM. Every time
the BND button @ is pressed, the display will
change as:
Loudness Effect
In order to turn on/off the loudness effect, use
the LD button 2 for 2 seconds or longer. Every
time the LD button 2 is pressed and held for 1
second or longer, the loudness effect switches
on and off.
FM1 ➜ FM2 ➜ FM3 ➜ AM ➜ FM1
3) Press the SRCH Left/Right button #, then
the station at which there is a broadcast will
be selected (Seek selection).
When the loudness effect is on, the display will show
“LD”.
*
Mute
Use this function to turn off the sound immedi-
ately.
Switching the Clock Display
Press the MUTE button %. The sound turns off
and “MUTE” appears on the display. Press the
MUTE button again to cancel the mute mode.
Every time the DISP button 6 is pressed, the
display will change between the operation mode
and the clock display.
Manual Tuning
Setting the Clock
1) Press the BND button @, then select FM1,
1) Press the DISP button 6 to display the clock
FM2, FM3 or AM.
display.
2) Press and hold the BND button @ for 1 sec-
ond or longer, then the display will show
“MANU”, which means that a manual selec-
tion function is on.
2) Press and hold the DISP button 6 for 1 sec-
ond or longer.
3) Press the SRCH Left button #, then set the
current hour.
3) Press the SRCH Left/Right button # and
4) Press the SRCH Right button #, then set the
select the right station.
current minute.
5) Press the DISP button 6, then the clock is
Seek Tuning
set.
1) Press the BND button @, then select FM1,
Notes:
FM2, FM3 or AM.
If you select another operation mode while you are
setting the clock, the clock setting operation will be
canceled.
•
2) If the “MANU” on the display is on, press and
hold the BND button @ for 1 second or
longer. When the “MANU” display is off, the
Seek Selection function is on.
If you remove the vehicle’s battery for a check or
repair, the clock will be reset, so you must set it again.
•
3) Press the SRCH Left/Right button #, then
when it selects the station in which there is a
broadcast, it automatically stops.
BD316
11
3) Press and hold the ISR button 5 for 2 sec-
Preset Memory Function
onds or longer.
Preset Memory Function can store up to 24 sta-
tions: six stations for each of FM1, FM2, FM3
and AM.
Recalling ISR
Press the ISR button 5 then the display will
show “ISR”, then the radio station previously
memorized will be selected. Press the ISR but-
ton 5 again to disengage the unit from the
Recalling ISR function.
Note:
When the present memory function is used, all the
content of the memory will be erased.
•
Manual memory function
1) Press the BND button @, and select the
Area Change
Use this function when you are using the car
stereo anywhere outside the U.S.
band you want to store in the memory.
2) Press the SRCH Left/Right button # then
select the station you want to store in the
memory.
Switchable frequency spacing
This car stereo is initially set to tune in frequen-
cy intervals of 10 kHz for AM and 200 kHz for
FM, the standard calibrations in the U.S. When
using the unit outside the U.S., use the following
procedure to switch the frequency range.
The table below lists the frequency specifica-
tions for the U.S. and other countries.
3) Press and hold the Preset button 0 for 2
seconds or longer, then the station will be
stored in the memory.
Auto store function (Automatic Station Store)
1) Press the BND button @, then select the
band you want to store in the memory.
Initial Setting New Setting
(U.S. standard) (outside U.S.)
2) Press and hold the AS button 9 for 2 sec-
onds or longer, then the station at which the
reception is the strongest will be automatical-
ly stored in the memory.
Frequency
spacing
10 kHz
530 to
9 kHz
531 to
AM
FM
Note:
Frequency
range
When the number of stations stored is less than six,
the previous content of the memory for each direct
button will be retained.
•
1,710 kHz 1,629 kHz
Frequency
spacing
200 kHz
87.9 to
50 kHz
87.5 to
Preset Scanning (Preset Station Scan)
Frequency
range
When the PS button 9 is pressed, the preset
memory numbers flash and the stations are
tuned in for 7 seconds each in the order in which
they were stored. Press the PS button again to
cancel the preset scanning mode.
107.9 MHz 108 MHz
Switching the area change
Outside U.S. (New Setting)
While pressing the BND button @, press the
SRCH Left button #, then “outside U.S.” will be
selected.
Instant Station Recall (ISR)
Inside U.S. standard (Initial Setting)
With this function, a specific radio station can be
recalled from any mode.
While pressing the BND button @, press the
SRCH Right button #, then the “U.S. standard”
will be selected.
ISR memory
1) Press the FNC button 3, then select the
radio mode.
2) Select the radio station which you want to
store in the memory.
12
BD316
Selecting Tracks (songs)
CD Mode Operations
Press the SRCH Left/Right button #.
: Playback will start from the next track.
: Playback will start from the beginning of
the track currently playing. When this
button is pressed again, the CD will play
from the previous track.
Loading a Disc
Insert the disc into the CD insertion slot with its
label side up, then the CD will start playing.
For 5-inch (12 cm) CD For 3-inch (8 cm) single CD
Fast-Forward and Fast-Backward
Press and hold the SRCH Left/Right button #.
: To fast-forward
: To fast-backward
Pressing the SRCH Left/Right button for 1 second or
*
When inserting a single CD (3”(8 cm)), insert it from
the center of the slot.
*
longer will move forward or backward 5 times faster
than normal play, and pressing it for 3 seconds or
longer will do the operation 30 times faster.
When inserting a single CD (3”(8 cm)), do not con-
nect an adapter.
*
Scan Play (Intro Music Scan)
Press the SCN button 9, then the display
shows “SCN”, then the CD will play the first 10
seconds of each track of the whole disc. Press
the SCN button 9 again to disengage the unit
from scan play.
Press the DISP button 6, then the display will show
the play time.
*
Notes:
Some CDs recorded in CD-R mode may not be
usable.
•
A scan play will start from the track following the one
*
currently playing.
Even when recorded in CD-R/W mode, some CDs
may not be usable.
•
Repeat Play
Press the RPT button 8, then the display shows
“RPT”, then the track currently playing will be
played repeatedly. Press the RPT button 8
again to disengage the unit from repeat play.
Listening to the Disc already Inserted
Press the FNC button 3 to select the CD mode,
the CD will start playing.
Stopping (pausing) Playback
Random Play
Press the Play/Pause button %.
Press the Play/Pause button % again to resume
playback.
Press the RDM button 7, then the display will
show “RDM”, then the entire tracks on the disc
will be played at random. Press the RDM button
7 again to disengage the unit from random play.
Ejecting the CD
Press the Eject button 4, then the CD will be
ejected.
Note:
If the ejected CD is left as it is, it will be reloaded after
15 seconds. However, single CDs will not be
reloaded, so make sure to remove them.
•
Top Function
Press the TOP button @, then the CD will start
playing from the first song (track number 1).
BD316
13
9. TROUBLESHOOTING
Problem
Cause
Solution
Power does not turn on.
(No sound is produced.)
Fuse is blown.
Replace with a fuse of the same
amperage. If the fuse blows again,
consult your store of purchase.
Incorrect wiring.
Consult your store of purchase.
Compact disc cannot be
loaded.
Another compact disc is
already loaded.
Eject the compact disc before loading
the new one.
Sound skips or is noisy.
Compact disc is dirty.
Clean the compact disc with a soft
cloth.
Compact disc is heaviiy
scratched or warped.
Replace with a compact disc with no
scratches.
Let dry for about 1 hour with the
power on.
Sound is bad directly after Water droplets may form
power is turned on.
on the internal lens when
the car is parked in a
humid place.
Nothing happens when
buttons are pressed.
Display is not accurate.
Microprocessor has
malfunctioned due to
noise, etc.
Turn off the power, then press the
DCP Release button 1 and remove
the DCP.
Press the reset button for about 2
seconds with a thin rod.
Reset button
DCP or source unit
connectors are dirty.
Wipe the dirt off with a soft cloth
moistened with cleaning alcohol.
14
BD316
10. ERROR DISPLAYS
■ To protect the system, this unit has been equipped with self diagnostic functions. If a fault
arises, a warning is issued by various error displays. Follow the corrective measures and
remove the fault.
Error Display
CD ER2
Corrective Measure
This error display indicates that a fault has arisen in the
mechanism of the source unit (for example, the disc cannot be
ejected).
➜ Check the source unit.
CD ER3
CD ER6
This error display indicates that the pickup focus is off because
of a scratched disc or some other factor during source unit play.
➜ Check the compact disc.
This indicates that the CD’s TOC (table of contents) cannot be
read, for example because the selected disc is upside-down.
BD316
15
11. SPECIFICATIONS
FM Tuner
General
Frequency Range: 87.9 MHz to 107.9 MHz
Usable Sensitivity: 11 dBf
Power Supply Voltage: 14.4 V DC (10.8 V to 15.6
V allowable), negative ground
50 dB Quieting Sensitivity: 17 dBf
Alternate Channel Selectivity: 75 dB
Stereo Separation (1 kHz): 35 dB
Frequency Response (±3 dB): 30 Hz to 15 kHz
Current Consumption: Less than 15 A
Speaker Impedance: 4 Ω (4 Ω to 8 Ω allowable)
Weight: 3.97 lb. (1.8 kg)
Dimensions:
7” (178 mm) Width × 2” (50 mm) Height ×
6-1/8” (155 mm) Depth
AM Tuner
7”
(178 mm)
2”
(50 mm)
Frequency Range: 530 kHz to 1,710 kHz
Usable Sensitivity: 25 µV
CD Player
System: Compact disc audio system
Usable Discs: Compact disc
Frequency Response: 10 Hz to 20 kHz (±1 dB)
Signal-to-Noise Ratio: 100 dB (1 kHz) IHF-A
Dynamic Range: 95 dB (1 kHz)
7-3/8”
(188 mm)
2-1/4”
(58 mm)
Notes:
Specifications comply with EIA Standards.
•
•
Audio
Maximum Power Output:
Specifications and design are subject to change with-
out notice for further improvement.
180 W (45 W × 4 ch)
Continuous Average Power Output:
17 W × 4, into 4 Ω, 20 Hz to 20 kHz,1%THD
Bass Control Action (30 Hz): ±13 dB
Treble Control Action (10 kHz): ±10 dB
Line Output (with CD 1 kHz, 10 kΩ): 1.8 V
16
BD316
|