Owner’s manual
AM/FM CD PLAYER
•
•
Clarion Co., Ltd.
PE-2557K
280-7913-01
All Rights Reserved. Copyright © 2003: Clarion Co., Ltd.
2003/04 (AB)
Display Items
Handling Compact Discs
2. PRECAUTIONS
•
•
Do not use compact discs that have large
scratches, are misshapen, cracked, etc. Use of
such discs may cause misoperation or damage.
To remove a compact disc from its storage case,
press down on the center of the case and lift the
disc out, holding it carefully by the edges.
Use only compact discs bearing the
or
Z-Enhancer Plus indication
mark.
1. When the inside of the car is very cold and the
player is used soon after switching on the
heater moisture may form on the disc or the
optical parts of the player and proper playback
may not be possible. If moisture forms on the
disc, wipe it off with a soft cloth. If moisture
forms on the optical parts of the player, do not
use the player for about one hour. The
condensation will disappear naturally allowing
normal operation.
CAUTION
Do not play heart-shaped, octagonal, or other
specially shaped compact discs.
Operation status indication
Titles, frequency, PS names, clock, etc.
are displays.
USE OF CONTROLS, ADJUSTMENTS, OR
PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN, MAY
RESULT IN HAZARDOUS RADIATION
EXPOSURE.
Some CDs recorded in CD-R/CD-RW mode
may not be usable.
• Do not use commercially available CD
protection sheets or discs equipped with
stabilizers, etc. These may damage the disc or
cause breakdown of the internal mechanism.
THE COMPACT DISC PLAYER and MINI DISC
PLAYER SHOULD NOT BE ADJUSTED OR
REPAIRED BY ANYONE EXCEPT PROPERLY
QUALIFIED SERVICE PERSONNEL.
Preset channel indication (1 to 6)
Disc number indication (1 to 12)
Handling
•
Compared to ordinary music CDs, CD-R and
CD-RW discs are both easily affected by high
temperature and humidity and some of CD-R
and CD-RW discs may not be played. Therefore,
do not leave them for a long time in the car.
Storage
2. Driving on extremely bumpy roads which
cause severe vibration may cause the sound
to skip.
• Do not expose compact discs to direct sunlight
or any heat source.
CHANGES OR MODIFICATIONS NOT
EXPRESSLY APPROVED BY THE
MANUFACTURER FOR COMPLIANCE COULD
VOID THE USER’S AUTHORITY TO OPERATE
THE EQUIPMENT.
• Do not expose compact discs to excess
humidity or dust.
• Do not expose compact discs to direct heat
from heaters.
• New discs may have
some roughness
3. This unit uses a precision mechanism. Even
in the event that trouble arises, never open
the case, disassemble the unit, or lubricate
the rotating parts.
Ball-point pen
Roughness
around the edges. If
such discs are used,
the player may not
work or the sound
may skip. Use a ball-
point pen or the like
to remove any
INFORMATION FOR USERS:.
Cleaning
CHANGES OR MODIFICATIONS TO THIS
PRODUCT NOT APPROVED BY THE
MANUFACTURER WILL VOID THE
WARRANTY AND WILL VIOLATE FCC
APPROVAL.
• To remove fingermarks and dust, use a soft
cloth and wipe in a straight line from the center
of the compact disc to the circumference.
Stereo indication
: Mute indication
roughness from the edge of the disc.
: Disc indication
• Do not use any solvents, such as commercially
available cleaners, anti-static spray, or thinner
to clean compact discs.
• After using special compact disc cleaner, let
the compact disc dry off well before playing it.
: Enter indication
•
Never stick labels on the surface of the compact
disc or mark the surface with a pencil or pen.
: Scan indication
: Repeat indication
: Random indication
: Manual indication
• Never play a compact disc with any
cellophane tape or other glue on it or with
peeling off marks. If you try to play such a
compact disc, you may not be able to get it
back out of the CD player or it may damage
the CD player.
: MAGNA BASS EXTEND indication
LCD Screen
In extreme cold, the screen movement may slow down and the screen may darken, but this is normal.
The screen will recover when it returns to normal temperature.
Be sure to unfold and read the next page. /
8
DXZ435
DXZ435
3
DXZ435
4
[TITLE] button
3.CONTROLS /
/
4. NOMENCLATURE
• Use the button to input a title in the CD
changer mode.
Note:
• Use the button to scroll the title during CD-
text play or MD changer play in the MD
changer mode.
Source unit /
/
• Be sure to read this chapter referring to the front diagrams of chapter “3. CONTROLS” on page 5 (unfold).
Names of the Buttons and their Functions
[UP], [DN] buttons
[
]
[
[
]
CD SLOT
ROTARY
• Select the disc.
[RELEASE] button
• Press the [RELEASE] button to unlock the
[UP], [DN] buttons
• Select the disc.
[RDM] button
]
[
]
RELEASE
Q
• Perform random play. Also perform disc
random play when the button is pressed and
held for 1 second or longer.
DCP.
[DIRECT] buttons
• Store a station into memory or recall it
directly while in the radio mode.
[ROTARY] knob
• Adjust the volume by turning the knob
clockwise or counterclockwise.
• Use the knob to perform various settings.
[RPT] button
[RDM] button
• Perform random play while in the CD mode.
[
]
]
]
Z+
[FNC]
[A-M]
[BND]
• Perform repeat play. When this button is
pressed and held for 1 second or longer,
disc repeat play is performed.
[
SW-VOL
[CD SLOT]
• CD insertion slot.
[RPT] button
• Repeat play while in the CD mode.
[
ISR
[BND] button
• Move the next disc in increasing order.
[Q] button
[SCN] button
• Eject a CD when it is loaded into the unit.
• Perform scan play for 10 seconds of each
track while in the CD mode.
[SCN] button
[a], [d]
[Z+] button
• Perform scan play for 10 seconds of each
track. Disc scan play is performed when the
button is pressed and held for 1 second or
longer.
• Use the button to select one of the 3 types of
sound characteristics already stored in
memory.
[
]
DIRECT
[
] button
[
]
• Play or pause a CD while in the CD mode.
[
], [
DN UP
]
[a], [d] buttons
[
]
[
]
DISP
SCN
[SW-VOL] button
• Adjust sub woofer volume.
The volume is adjusted in the range 6.
• Select a station while in the radio mode or
select a track when listening to a CD. These
buttons are used to make various settings.
• Press and hold the button for 1 second or
longer to switch the fast-forward/fast-
backward.
[
] button
[
]
[
]
TITLE
RPT
• Play or pause a CD, MD or DVD.
[
]
[
]
RDM
P/A
[ISR] button
[a], [d] buttons
• Recall ISR radio station in memory.
• Press and hold for 2 seconds or longer: Store
current station into ISR memory (radio mode
only).
• Select a track when listening to a disc.
• Press and hold the button for 1 second or
longer to switch the fast-forward/fast-
backward.
[BND] button
• Switch the band, or seek tuning or manual
tuning while in the radio mode.
• Play a first track while in the CD mode.
[DISP] button
• Switch the display indication (Main display,
Sub display, Clock display).
[A-M] button
●When the TV is connected
∗ For details, see the section “TV
operations”.
• Use the button to switch to the audio mode
(bass/treble, balance/fader Z-Enhancer Plus,
Magna Bass Extended adjustment)
[TITLE] button
• Use the button to input a title in the CD
mode.
[P/A] button
• Press and hold the button for 1 second or
longer to enter the adjust mode.
[FNC] button
• Perform preset scan while in the TV mode.
When the button is pressed and held for 2
seconds or longer, auto store is performed.
• Press the button to turn on the power.
Press and hold the button for 1 second or
longer to turn off the power.
[P/A] button
• Perform preset scan while in the radio mode.
When the button is pressed and held, auto
store is performed.
• Switches the operation mode among the
radio mode, etc.
[
] button
• Switch the TV picture mode or VTR (external)
picture mode.
[DIRECT] buttons
• Store a station into memory or recall it
directly.
Major button operations when external equipment is
connected to this unit
[a], [d] buttons
• Select a station.
[DISP] button
●When the CD/MD/DVD changer
Note: Be sure to unfold this page and refer to the front diagrams as you read each chapter.
• When the button is pressed and held,
[BND] button
• Switch the band.
• When the button is pressed and held for 1
second or longer, switch seek tuning or
manual mode.
is connected
switches the disc titles or track titles while in
∗ For details, see the section “CD/MD
the MD changer mode.
• When the button is pressed and held,
switches the user titles or track titles, etc.
provided with the DVD changer.
changer operations”. For the DVD
changer, refer to the Owner’s Manual
while in the CD changer mode.
5
DXZ435
6
DXZ435
DXZ435
7
5. DCP
The control panel can be detached to prevent
theft. When detaching the control panel, store it
in the DCP (DETACHABLE CONTROL PANEL)
case to prevent scratches.
Storing the DCP in the DCP Case
Hold the DCP, in the orientation as shown in the
figure below, and put it into the supplied DCP
case. (Ensure the DCP is in the correct
orientation.)
We recommend taking the DCP with you when
leaving the car.
DCP
Removing the DCP
1. Press the [FNC] button for 1 second or
longer to switch off the power.
2. Press in the [RELEASE] button.
DCP case
[
]
RELEASE button
CAUTION
• The DCP can easily be damaged by
shocks. After removing it, be careful not to
drop it or subject it to strong shocks.
• When the Release button is pressed and
the DCP is unlocked, the car’s vibrations
may cause it to fall. To prevent damage to
the DCP, always store it in its case after
detaching it. (ee figure below.)
∗ The DCP is unlocked
3. Remove the DCP.
• The connector connecting the main unit
and the DCP is an extremely important
part. Be careful not to damage it by
pressing on it with fingernails,
screwdrivers, etc.
DCP Rear Panel
Main Unit Front
DCP
Attaching the DCP
1. Insert the right side of the DCP into the main
unit.
DCP
connector
2. Insert the left side of the DCP into the main
unit.
Main unit connector
Note:
• If the DCP is dirty, wipe off the dirt with a soft, dry
cloth only.
2.
DCP
1.
DXZ435
9
Functions of Remote Control Unit Buttons
6. REMOTE CONTROL
Mode
Button
CD/MD changer
DVD changer
Radio
CD
Receiver for remote control unit
TV
Switches among radio, CD, CD/MD changer, DVD changer, TV and AUX.
[FUNC]
Plays the first track.
Top play.
Moves the next disc
in increasing order.
Switches reception
band.
Switches reception
band.
[BAND]
Operating range: 30˚ in all directions
Increases and decreases volume (in all modes).
[
[
] , [
] , [
]
]
Signal transmitter
Moves preset
channels up and
down.
Moves tracks up and down.
When pressed and held for 1 second:
Fast-forward/fast-backward.
Moves preset
channels up and
down.
Remote control unit
No function.
Switches between playback and pause.
No function.
[
]
[
]
]
[
[
]
DUAL ZONE
FUNC
]
[
],[
Turns mute on and off.
[MUTE]
[
[
],[
]
]
Recalls ISR radio station in memory.
Press and hold for 2 seconds or longer: Stores current station into ISR memory
(radio mode only).
BAND
[ISR]
[
]
ISR
[
]
[
[
]
DISP
MUTE
Switches among main display, sub display, clock display.
[DISP]
]
[
]
RDM
SCN
[SCN]
Scan play.
Preset scan.
Preset scan.
Scan play.
When pressed and
held for 2 seconds:
Auto store.
When pressed and
held for 2 seconds:
Auto store.
When pressed and
held for 1 second:
Disc scan play.
[
]
RPT
[RPT]
Repeat play.
No function.
No function.
No function.
Repeat play.
When pressed and
held for 1 second:
Disc repeat play.
Inserting the Batteries
1. Turn the remote control unit over, then slide the
rear cover in the direction of the arrow.
AA (SUM-3, IECR-6/1.5V)
Batteries
2. Insert the AA (SUM-3, IECR-6/1.5V) batteries
that came with the remote control unit facing in
the directions shown in the figure, then close
the rear cover.
[RDM]
Random play.
Switches between TV
and VTR.
Random play.
When pressed and
held for 1 second:
Disc random play.
Notes:
Using batteries improperly can cause them to
explode. Take note of the following points:
Rear cover
• When replacing batteries, replace both batteries
with new ones.
∗ Some of the corresponding buttons on the main unit and remote control unit have different functions.
∗ [DUAL ZONE] button is not available.
• Do not short-circuit, disassemble or heat batteries.
• Do not dispose of batteries into fire or flames.
• Dispose of spent batteries properly.
Rear side
10
DXZ435
DXZ435
11
Basic Operations
7. OPERATIONS
Basic Operations
∗ The factory default setting is “B<Q 1>”.
(Adjustment 1/1.25/1.5/2)
“Z+ OFF” ➜ “B-BOOST” ➜ “IMPACT” ➜
“EXCITE” ➜ “CUSTOM” ➜ “Z+ OFF” ...
Note:Be sure to read this chapter referring to the front diagrams of
chapter “3. CONTROLS” on page 5 (unfold).
5. When the adjustment is complete, press the
[A-M] button several times until the function
mode is reached.
• B-BOOST
• IMPACT
: bass emphasized
: bass and treble
emphasized
Adjusting the volume
Turning the [ROTARY] knob clockwise
increases the volume; turning it
counterclockwise decreases the volume.
∗ The volume level is from 0 (minimum) to 33
CAUTION
Be sure to lower the volume before
• EXCITE
: bass and treble
emphasized mid de-
emphasized
switching off the unit power or the ignition
key. The unit remembers its last volume
setting. If you switch the power off with the
volume up, when you switch the power back
on, the sudden loud volume may hurt your
hearing and damage the unit.
Adjusting the treble (Gain,
Frequency)
This adjustment can be performed when the Z-
Enhancer Plus is set to “CUSTOM”.
(maximum).
• CUSTOM
• Z+ OFF
: user custom
: no sound effect
1. Press the [A-M] button and select “TREBLE”.
Switching the display
Press the [DISP] button to select the desired
display.
2. Turning the [ROTARY] knob clockwise
emphasizes the treble; turning it
Adjusting the tone
Press the [A-M] button and select the item to
adjust. Each time you press the [A-M] button,
the item changes as following order:
Turning on/off the power
Note:
• Be careful about using this unit for a long time
without running the engine. If you drain the car’s
battery too far, you may not be able to start the
engine and this can reduce the service life of the
battery.
counterclockwise attenuates the treble.
∗ The factory default setting is “T<G 0>”.
(Adjustment range: –6 to +6)
Each time you press the [DISP] button, the
display switches in the following order:
Main display
Sub display
Clock display
Main display
●When “B-BOOST” is set
3. Press the [d] or [a] button to select
“B-BOOST” ➜ “BAL 0” ➜ “FAD 0” ➜ Last
function mode.
“T<F 10>”.
Turninng the [ROTARY] knob clockwise or
counterclockwise to select the frequency.
∗ The factory default setting is “T<F 10>”.
(Adjustment 10 kHz/15 kHz)
●When “IMPACT” is set
1. Press the [FNC] button.
“IMPACT” ➜ “BAL 0” ➜ “FAD 0” ➜ Last
function mode.
2. The illumination and display on the unit light
up. The unit automatically remembers its last
operation mode and will automatically switch
to display that mode.
●When “EXCITE” is set
4. When the adjustment is complete, press the
[A-M] button several times until the function
mode is reached.
“EXCITE” ➜ “BAL 0” ➜ “FAD 0” ➜ Last
function mode.
3. Press and hold the [FNC] button for 1
second or longer to turn off the power for the
unit.
Note:
• System check
The first time this unit is turned on after the wire
connections are completed, it must be checked
what equipment is connected. When the power is
turned on, “SYSTEM” and “PUSH PWR” appear
in the display alternately, so press the [FNC]
button. The system check starts within the unit.
When the system check is complete, press the
[FNC] button again.
●When “CUSTOM” is set
“BASS” ➜ “TREBLE” ➜ “BAL 0” ➜ “FAD
0” ➜ Last function mode.
Adjusting the balance
1. Press the [A-M] button and select “BAL 0”.
●When “Z+ OFF” is set
2. Turning the [ROTARY] knob clockwise
emphasizes the sound from the right
speaker; turning it counterclockwise
“BAL 0” ➜ “FAD 0” ➜ Last function mode.
emphasizes the sound from the left speaker.
∗ The factory default setting is “BAL 0”.
(Adjustment range: L13 to R13)
Adjusting the bass (Gain,
Frequency, Q-curve)
This adjustment can be performed when the Z-
Enhancer Plus is set to “CUSTOM”.
∗ Once selected, the preferred display becomes
the display default. When a function
adjustment such as volume is made, the
screen will momentarily switch to that
function’s display, then revert back to the
preferred display several seconds after the
adjustment.
3. When the adjustment is complete, press the
[A-M] button several times until the function
mode is reached.
1. Press the [A-M] button and select “BASS”.
Selecting a mode
1. Press the [FNC] button to change the
operation mode.
2. Turning the [ROTARY] knob clockwise
emphasizes the bass; turning it
∗ When you have entered a title in a CD, it
appears in the sub display. If you have not
entered a title, “NO TITLE” appears in the title
display instead. For information on how to
enter a title, refer to the subsection “Entering
titles” in section “Operations Common to
Each Mode”.
Adjusting the fader
1. Press the [A-M] button and select “FAD 0”.
counterclockwise attenuates the bass.
∗ The factory default setting is “B<G 0>”.
(Adjustment range: –6 to +6)
2. Each time you press the [FNC] button, the
operation mode changes in the following
order:
2. Turning the [ROTARY] knob clockwise
emphasizes the sound from the front
speakers; turning it counterclockwise
emphasizes the sound from the rear
speakers.
3. Press the [d] or [a] button to select “B<F
Radio mode ➜ CD mode ➜ CD changer
mode ➜ MD changer mode ➜ DVD changer
mode ➜ TV mode ➜ AUX mode ➜ Radio
mode...
∗ External equipment not connected with
CeNET is not displayed.
60>”.
Turninng the [ROTARY] knob clockwise or
counterclockwise to select the frequency.
∗ The factory default setting is “B<F 60>”.
(Adjustment 60/100/200 Hz)
Setting the Z-Enhancer Plus
This unit are provided with 3 types of sound tone
effects stored in memory. Select the one you prefer.
∗ The factory default setting is “FAD 0”.
(Adjustment range: F12 to R12)
3. When the adjustment is complete, press the
[A-M] button several times until the function
mode is reached.
4. Press the [d] or [a] button to select “B<Q 1>”.
∗ The factory default setting is “Z+ OFF”.
Turninng the [ROTARY] knob clockwise or
counterclockwise to select the Q-curve.
Each time you press the [Z+] button, the tone
effect changes in the following order:
12
DXZ435
DXZ435
13
Basic Operations
Radio Operations
Radio Operations
Adjusting the Z-Enhancer Plus
1. Press the [Z+] button and select the Z-
Enhancer Plus mode to adjust.
FM reception
Manual tuning
Auto store
®
For enhanced FM performance the
There are 2 ways available: Quick tuning and
step tuning.
Auto store is a function for storing up to 6
stations that are automatically tuned in
sequentially. If 6 receivable stations cannot be
received, a previously stored station remains
unoverwritten at the memory position.
tuner includes signal actuated stereo control,
Enhanced Multi AGC, Impulse noise reduction
curcuits and Multipath noise reduction circuits.
2. Press the [A-M] button and turning the
[ROTARY] knob clockwise adjusts in the +
direction; turning it counterclockwise adjusts
in the – direction.
When you are in the step tuning mode, the
frequency changes one step at a time. In the
quick tuning mode, you can quickly tune the
desired frequency.
1. Press the [BND] button and select the
Listening to the radio
1. Press the [FNC] button and select the radio
mode. The frequency or PS appears in the
display.
desired band (FM or AM).
●When “B-BST 0” is selected, you can ad-
just the bass in the range of –3 to 3.
1. Press the [BND] button and select the
desired band (FM or AM).
2. Press and hold the [P/A] button for 2
seconds or longer. The stations with good
reception are stored automatically to the
preset channels.
∗ If “MANU” is not lit in the display, press and
hold the [BND] button for 1 second or longer.
“MANU” is lit in the display and manual tuning
is now available.
●When “IMPACT 0” is selected, you can
adjust the bass and treble in the range of
–3 to 3.
∗ PS: Programme service name
2. Press the [BND] button and select the radio
∗ If auto store is performed in the FM bands, the
stations are stored in FM3 even if FM1 or FM2
was chosen for storing stations.
●When “EXCITE 0” is selected, you can ad-
just the bass and treble in the range of –3
to 3.
∗ Press and hold the [Z+] button for 2 seconds
or longer to change to the “CUSTOM” mode.
Bass/treble characteristics become flat and
the indication “Z+FLAT” is shown in the
display.
band. Each time the button is pressed, the
radio reception band changes in the following
order:
2. Tune in a station.
●Quick tuning:
Press and hold the [a] or [d] button for 1
FM1 ➜ FM2 ➜ FM3 ➜AM ➜ FM1...
Preset scan
Preset scan receives the stations stored in
preset memory in order. This function is useful
when searching for a desired station in memory.
second or longer to tune in a station.
3. Press the [a] or [d] button to tune in the
●Step tuning:
desired station.
Press the [a] or [d] button to manually
tune in a station.
Press the [Z+] button again to change to the
“Z+ OFF” mode.
Tuning
1. Press the [P/A] button.
There are 3 types of tuning mode available, seek
tuning, manual tuning and preset tuning.
2. When a desired station is tuned in, press the
[P/A] button again to continue receiving that
station.
Recalling a preset station
A total of 24 preset positions (6-FM1, 6-FM2, 6-
FM3, 6-AM) exist to store individual radio
stations in memory. Pressing the corresponding
[DIRECT] button recalls the stored radio
frequency automatically.
Adjusting MAGNA BASS EXTEND
The MAGNA BASS EXTEND does not adjust
the low sound area like the normal sound
adjustment function, but emphasizes the deep
bass sound area to provide you with a dynamic
sound.
Note:
Seek tuning
1. Press the [BND] button and select the
desired band (FM or AM).
• Be careful not to press and hold the [P/A] button
for 2 seconds or longer, otherwise the auto store
function is engaged and the unit starts storing
stations.
∗ If “MANU” is lit in the display, press and hold
the [BND] button for 1 second or longer.
“MANU” in the display goes off and seek
tuning is now available.
1. Press the [BND] button and select the
desired band (FM or AM).
∗ The factory default setting is off.
Instant station recall (ISR)
2. Press the corresponding [DIRECT] button to
1. Press and hold the [A-M] button for 1
second or longer to turn on the MAGNA
BASS EXTEND effect. “M-B EX” lights in
the display.
recall the stored station.
Instant station recall is a special radio preset
that instantly accesses a favorite radio station at
a touch of a button. The ISR function even
operates with the unit in other modes.
2. Press the [a] or [d] button to
∗ Press and hold one of the [DIRECT] buttons
for 2 seconds or longer to store that station
into preset memory.
automatically seek a station.
When the [d] button is pressed, the station is
sought in the direction of higher frequencies; if
the [a] button is pressed, the station is sought
in the direction of lower frequencies.
2. Press and hold the [A-M] button for 1 second
or longer to turn off the MAGNA BASS
EXTEND effect. “M-B EX” goes off from the
display.
●ISR memory
Manual memory
1. Select the desired station with seek tuning,
manual tuning or preset tuning.
1. Select the station that you wish to store in ISR
memory.
2. Press and hold the [ISR] button for 2 seconds
Adjusting the subwoofer
When you default select one of mode (LPF50,
LPF80, LPF120).
or longer.
2. Press and hold one of the [DIRECT] buttons
for 2 seconds or longer to store the current
station into preset memory.
●Recalling a station with ISR
In any mode, press the [ISR] button to turn on
the radio function and tune the selected radio
station. “ISR” appears in the display. Press the
[ISR] button again to return to the previous
mode.
∗ The factory default setting is “S-VOL 0”.
(Adjustment range: –6 to +6)
1. Press the [SW-VOL ] button to select the
subwoofer volume increases or decreases.
2. Press and hold the [SW-VOL ] button, the
subwoofer volume automatically increases or
decreases.
14
DXZ435
DXZ435
15
CD Operations
CD Operations
Operations Common to
Each Mode
Note:
Loading a CD
Scan play
• If the CD playing is not a CD-text CD or no user
title has been input, “NO TITLE” appears in the
display.
Insert a CD into the centre of the CD SLOT with
the labeled side facing up. “LOADING” appears
in the display, the CD enters into the slot, and
the play starts.
The scan play locates and plays the first 10
seconds of each track on a disc automatically.
This function continues on the disc until it is
cancelled.
Turning the screen saver function
on or off
This unit is provided with the screen saver
function which allows you to show various kinds
of patterns and characters in the Operation
Status indication area of the display in a random
order. You can turn on and off this function.
Ejecting a CD
1. Press the [Q] to eject the CD. Take it out
from the ejected position.
∗ The scan play is useful when you want to select a
desired track.
For CD (12 cm)
For single CD (8 cm)
CD SLOT
1. Press the [SCN] button to start scan play.
Note:
“SCN” lights in the display.
If the button operation is performed with the
screen saver function on, the operation display
corresponding to the button operation is shown
for about 30 seconds and the display returns to
the screen saver display.
• If you force a CD into before auto reloading, this
can damage the CD.
∗ If a CD (12 cm) is left in the ejected position for 15
seconds, the CD is automatically reloaded (Auto
reload).
2. To cancel the scan play, press the [SCN]
button again. “SCN” goes off from the
display and the current track continues to
play.
∗ 8 cm CDs are not auto reloaded. Be sure to remove
it when ejected.
∗ The factory default setting is “SS”.
Repeat play
The repeat play continuously plays the current
track. This function continues automatically until
it is cancelled.
Notes:
1. Press and hold the [TITLE] button for 1
second or longer to switch to the adjustment
selection display.
• Never insert foreign objects into the CD SLOT.
• If the CD is not inserted easily, there may be
another CD in the mechanism or the unit may
require service.
Selecting a track
●Track-up
2. Press the [a] or [d] button to select
1. Press the [RPT] button. “RPT” lights in the
1. Press the [d] button to move ahead to the
“SCRN SVR”.
• Discs not bearing the
or
mark and
display and the current track is repeated.
beginning of the next track.
3. Press the [
] button.
CD-ROMs cannot be played by this unit.
• Some CDs recorded in CD-R/CD-RW mode may
not be usable.
2. To cancel the repeat play, press the [RPT]
button again. “RPT” goes off from the display
and normal play resumes.
2. Each time you press the [d] button, the
track advances ahead to the beginning of the
next track.
4. Turn the [ROTARY] knob clockwise or
counterclockwise to select the setting. Each
time you turn the [ROTARY] knob, the setting
changes in the following order:
Loading 8 cm compact discs
●Track-down
∗ No adapter is required to play an 8 cm CD.
OFF ➜ SS ➜ MESSAGE
Random play
1. Press the [a] button to move back to the
∗ Insert the 8 cm CD into the centre of the insertion
slot.
beginning of the current track.
The random play selects and plays individual
tracks on a disc in no particular order. This
function continues automatically until it is
cancelled.
5. Press the [
] button to store the setting.
2. Press the [a] button twice to move to the
6. Press the [TITLE] button to return to the
beginning of the previous track.
previous mode.
Listening to a CD already inserted
Press the [FNC] button to select the CD mode.
Play starts automatically. If no CD is loaded in
the unit, “NO DISC” appears in the display.
∗ The following illustration presents one of the
patterns which are shown when the screen
saver function is turned on.
1. Press the [RDM] button. “RDM” lights in the
display, an individual track is selected
randomly and play begins.
Fast-forward/fast-backward
●Fast-forward
Press and hold the [d] button for 1 second or
2. To cancel the random play, press the [RDM]
button again. “RDM” goes off from the
display and normal play resumes.
longer.
Pausing play
1. Press the [
●Fast-backward
] button to pause play.
“PAUSE” appears in the display.
Press and hold the [a] button for 1 second or
Entering MESSAGE INFORMATION
Message up to 30 characters long can be stored
in memory and displayed for any mode.
longer.
2. To resume CD play, press the [
again.
] button
Top function
* The factory default setting is “WELCOME TO
The top function resets the CD player to the first
track of the disc. Press the [BND] button to play
the first track (track No. 1) on the disc.
CLARION”.
Displaying CD titles
1. Press and hold the [TITLE] button for 1
second or longer to switch to the adjustment
selection display.
This unit can display title data for CD-text CDs
and user titles input with this unit.
1. Press the [DISP] button to display the title.
2. Press the [a] or [d] button to select
2. Each time you press and hold the [DISP]
button for 1 second or longer, the title
display changes in the following order:
“INPUT”.
3. Press the [
] button.
4. Press the [a] or [d] button to move the
User title (disc) ➜ CD-text title (disc) ➜ Artist
name ➜ CD-text title (track) ➜ User title
(disc)...
cursor.
16
DXZ435
DXZ435
17
Operations Common to Each Mode
Operations Common to Each Mode
5. Press the [DISP] button to select a character.
Each time you press the [DISP] button, the
character changes in the following orders:
6. Press the [DISP] button to select a character.
Each time you press the [DISP] button, the
character changes in the following order:
Adjusting the display contrast
You can adjust the display contrast to match the
angle of installation of the unit.
∗ The factory default setting is “5”. (Adjustment
level:1to 8)
Setting the clock
1. Press and hold the [TITLE] button for 1
second or longer to switch to the adjustment
selection display.
Numbers ➜ Symbols ➜ Capital letters ➜
Numbers…
Numbers ➜ Symbols ➜ Capital letters ➜
Numbers...
2. Press the [a] or [d] button to select
6. Turn the [ROTARY] knob to select the
7. Turn the [ROTARY] knob to select the
“CLOCK”.
1. Press and hold the [TITLE] button for 1
second or longer to switch to the adjustment
selection display.
desired character.
desired character.
3. Press the [
] button.
7. Repeat step 4 to 6 to enter up to 30
characters for message.
8. Repeat steps 5 to 7 to enter up to 8
characters for the title.
4. Press the [a] or [d] button to select the
2. Press the [a] or [d] button to select
hour or the minute.
“CONTRAST”.
8. Press and hold the [
] button for 2
9. Press and hold the [
] button for 2
5. Turn the [ROTARY] knob clockwise or
seconds or longer to store the message in
memory and cancel input message.
3. Turn the [ROTARY] knob clockwise or
seconds or longer to store the title into
memory and cancel title input mode.
counterclockwise to set the correct time.
∗ The clock is displayed in 12-hour format.
counterclockwise to adjust the contrast.
9. Press the [TITLE] button to return to the
4. Press the [TITLE] button to return to the
6. Press the [
memory.
] button to store the time into
previous mode.
previous mode.
Clearing titles
1. Select and play a CD in the CD changer or
tune in to a TV station for which you want to
clear the title.
7. Press the [TITLE] button to return to the
previous mode.
Note:
• You cannot set the clock when it is displayed with
only the ignition on. If you drain or remove the
car’s battery or take out this unit, the clock is
reset. While setting the clock, if another button or
operation is selected, the clock set mode is
canceled.
Setting LOW PASS FILTER
This function allows you to set the low-pass filter
sub-woofer output.
Setting the method for title scroll
Set how to scroll in CD-TEXT or MD.
∗ The factory default setting is “ON”.
2. Press the [DISP] button and display the sub.
∗ The factory default setting is “LPF 120”.
3. Press the [TITLE] button.
1. Press and hold the [TITLE] button for 1
second or longer to switch to the adjustment
selection display.
The display switches to the title input display.
1. Press and hold the [TITLE] button for 1
second or longer to switch to the adjustment
selection display.
4. Press the [BND] button.
2. Press the [a] or [d] button to select
5. Press and hold the [
] button for 2
2. Press the [a] or [d] button to select “SW
“SCROLL”.
seconds or longer to clear the title and
cancel title input mode.
LPF”.
3. Turn the [ROTARY] knob clockwise or
Entering titles
3. Turn the [ROTARY] knob clockwise or
counterclockwise to select the setting. Each
time you turn the [ROTARY] knob, the setting
changes in the following order:
counterclockwise and select “ON” or “OFF”.
Titles up to 8 characters long can be stored in
memory and displayed for CD, CD changer and
TV stations. The number of titles that can be
entered for each mode are as follows.
● ON:
AUX function
This system has an external input jack so you
can listen to sounds and music from external
devices connected to this unit.
To scroll automatically.
● OFF:
REAR ➜ LPF 50 ➜ LPF 80 ➜ LPF 120
Mode
CD mode
TV mode
Number of titles
50 titles
To scroll just 1 time when the title was
changed or the title key was pressed.
4. Press the [TITLE] button to return to the
previous mode.
20 titles
4. Press the [TITLE] button to return to the
previous mode.
Selecting AUX IN sensitivity
Make the following settings to select the
sensitivity when sounds from external devices
connected to this unit are difficult to hear even
after adjusting the volume.
CD changer mode
DCZ625 connected
CDC655Tz connected
CDC1255z connected
Number of titles
100 titles
Dimmer control
You can set the dimmer control on or off.
∗ The factory default setting is “ON”.
100 titles
50 titles
∗ The factory default setting is “MID”.
1. Press and hold the [TITLE] button for 1
second or longer to switch to the adjustment
selection display.
1. Press the [FNC] button to select the mode
you want to enter a title (CD, CD changer or
TV).
1. Press and hold the [TITLE] button for 1
second or longer to switch to the adjustment
selection display.
2. Press the [a] or [d] button to select
2. Select and play a CD in the CD changer or
tune in to a TV station for which you want to
enter the title.
“DIMMER”.
2. Press the [a] or [d] button to select “AUX
SENS”.
3. Turn the [ROTARY] knob clockwise to “ON”
or counterclockwise to “OFF”.
3. Turn the [ROTARY] knob clockwise or
counterclockwise as needed and select from
“HIGH”, “MID” or “LOW”.
3. Press the [DISP] button and display the sub.
4. Press the [TITLE] button to return to the
4. Press the [TITLE] button. The cursor position
previous mode.
flashes.
4. Press the [TITLE] button to return to the
5. Press the [a] or [d] button to move the
previous mode.
cursor.
18
DXZ435
DXZ435
19
CD/MD Changer Operations
8. OPERATIONS OF ACCESSORIES
CD/MD Changer Operations
2. To cancel disc scan play, press the [SCN]
button again. “DISC” and “SCN” go off from
the display and the current track continues to
play.
Selecting a MD
[DN] or [UP] button correspond to a MD load in
the MD changer. Press the [DN] or [UP] button
to select the desired disc.
∗ If a MD is not loaded in a slot of MD changer, “NO
DISC” appears in the display.
Notes:
CD/MD changer functions
• If the CD playing is not a CD-text CD or no user
When an optional CD/MD changer is connected
Repeat play
Repeat play continuously plays the current
track. This function continues automatically until
it is cancelled.
title has been input, “NO TITLE” appears in the
through the CeNET cable, this unit controls all
display.
CD/MD changer functions. This unit can control
a total of 2 changers.
Selecting a track
●Track-up
• If a CD-text CD is not input its disc title or a track
title, “NO TITLE” appears in the display.
Press the [FNC] button and select the CD(MD)
1. Press the [RPT] button. “RPT” lights in the
1. Press the [d] button to move ahead to the
changer mode to start play. If 2 CD(MD)
display and the current track is repeated.
beginning of the next track.
Switching disc titles and track titles
changers are connected, press the [FNC] button
2. To cancel repeat play, press the [RPT] button
again. “RPT” goes off from the display and
normal play resumes.
2. Each time you press the [d] button, the
track advances ahead to the beginning of the
next track.
(MD)
to select the CD(MD) changer for play.
This unit can display disc titles and track titles
already entered on MDs.
∗ Titles cannot be entered for MDs with this unit.
∗ If “NO MAG” appears in the display, insert the
magazine into the CD changer. “DISC CHK”
appears in the display while the player loads
(checks) the magazine.
●Track-down
Disc repeat play
1. Press the [a] button to move back to the
1. Press [DISP] button to display the title. The
After all the tracks on the current disc have
been played, disc repeat play automatically
replays the current disc over from the first track.
This function continues automatically until it is
cancelled.
∗ If “NO DISC” appears in the display, eject the
magazine and insert discs into each slot. Then,
reinsert the magazine back into the CD changer.
beginning of the current track.
disc title or track title is displayed.
2. Press the [a] button twice to move to the
2. Each time you press and hold the [DISP]
button for 1 second or longer, the display
toggles between the disc title and the track
title.
beginning of the previous track.
∗ If “NO DISC” appears in the display, load MDs into
the MD changer.
Fast-forward/fast-backward
●Fast-forward
Note:
1. Press and hold the [RPT] button for 1 second
or longer. “DISC” and “RPT” light in the
display and disc repeat play starts.
Note:
• Some CDs recorded in CD-R/CD-RW mode may
not be usable.
• If an MD is not input its disc title or a track title,
“NO TITLE” appears in the display.
Press and hold the [d] button for 1 second or
longer.
2. To cancel disc repeat play, press and hold
the [RPT] button again. “DISC” and “RPT” go
off from the display and normal play resumes
on the current track.
CAUTION
CD-ROM discs cannot be played from every
CD changer, it’s depended on the model.
●Fast-backward
Procedure to scroll a title
Press and hold the [a] button for 1 second or
Set “SCROLL” to “ON” or “OFF”.
longer.
(The factory default setting is “ON”. Refer to the
subsection “Turning the screen saver function
on or off” in section “Operation common to
each mode”.)
Random play
Random play selects and plays individual tracks
on the disc in no particular order. This function
continues automatically until it is cancelled.
Scan play
Scan play locates and plays the first 10 seconds
of each track on a disc automatically. This
function continues on the disc until it is cancelled.
∗ The scan play is useful when you want to select a
desired track.
Pausing play
1. Press the [
] button to pause play.
“PAUSE” appears in the display.
●When set to “ON”
2. To resume play, press the [
] button again.
The title is automatically kept scrolling.
●When set to “OFF”
1. Press the [RDM] button. “RDM” lights in the
display and random play begins.
Displaying CD titles
Press the [TITLE] button to scroll the title.
2. To cancel random play, press the [RDM]
button again. “RDM” goes off from the
display and normal play resumes.
1. Press the [SCN] button to start track
This unit can display title data for CD-text CDs
and user titles input with this unit.
scanning. “SCN” lights in the display.
2. To cancel the scan play, press the [SCN]
button again. “SCN” goes off from the display
and the current track continues to play.
Selecting a CD
[DN] or [UP] button correspond to a disc load in
the magazine.
∗ Title data for CD-text CDs can be displayed with
this unit only when it is connected to CDC655Tz.
Disc random play
●When connected to CDC655z or CDC1255z.
Press the [DISP] button to display the title.
●When connected to DCZ625 or CDC655Tz
1. Press the [DISP] button to display the title.
The disc random play selects and plays
individual tracks or discs automatically in no
particular order. This function continues
automatically until it is cancelled.
Press the [DN] or [UP] button to select the
desired disc.
∗ If a CD is not loaded in a slot of magazine, “NO
DISC” appears in the display.
Disc scan play
Disc scan play locates and plays the first 10
seconds of the first track on each disc in the
currently selected CD (MD) changer. This
function continues automatically until it is
cancelled.
1. Press and hold the [RDM] button for 1
second or longer. “DISC” and “RDM” light in
the display and disc random play starts.
2. Each time you press and hold the [DISP]
button for 1 second or longer, the title display
changes in the following order:
∗ Disc scan play is useful when you want to select a
desired CD (MD).
2. To cancel disc random play, press and hold
the [RDM] button again. “DISC” and “RDM”
go off from the display and normal play
resumes from the current track.
User title (disc) ➜ CD-text title (disc) ➜ Artist
title ➜ CD-text title (track) ➜ User title
(disc)…
1. Press and hold the [SCN] button for 1
second or longer. “DISC” and “SCN” light in
the display and disc scan play starts.
20
DXZ435
DXZ435
21
TV Operations
TV Operations
TV tuner functions
Manual tuning
Auto store
Setting the TV area
When an optional TV tuner is connected through
the CeNET cable, this unit controls all TV tuner
functions. To watch TV requires a TV tuner and
monitor.
There are 2 ways available: Quick tuning and
step tuning.
Auto store selects 6 TV stations automatically
and stores each one into preset memory.
When you select the TV area (TV reception
area), the TV tuner area setting changes.
When you are in the step tuning mode, the
frequency changes one step at a time. In the
quick tuning mode, you can quickly tune the
desired frequency.
If there are not 6 stations with good reception,
stations previously stored in memory remain
and only the strong stations are stored into
memory.
1. Press and hold the [TITLE] button for 1
second or longer to switch to the adjustment
selection display.
2. Press the [a] or [d] button to select “TV
Watching a TV
1. Press the [FNC] button and select the TV
1. Press the [BND] button and select the
1. Press the [BND] button and select the
AREA”.
desired band (TV1 or TV2).
desired TV band (TV1 or TV2).
3. Press the [
] button.
mode.
∗ If “MANU” is not lit in the display, press and
hold the [BND] button for 1 second or longer.
“MANU” lights in the display and manual
tuning is now available.
2. Press and hold the [P/A] button for 2
seconds or longer. The stations with good
reception are stored automatically to the
preset channels.
4. Turn the [ROTARY] knob clockwise or
counterclockwise to select the reception
area.
2. Press the [BND] button to select the desired
TV band (TV1 or TV2). Each time the button
is pressed, the input selection toggles
between TV1 and TV2.
5. Press the [
] button.
2. Tune in a station.
3. Press the [a] or [d] button to tune in the
6. Press the [TITLE] button to return to the
●Quick tuning:
Preset scan
desired TV station.
previous mode.
Press and hold the [a] or [d] button for 1
Preset scan allows the user to view each preset
position before it automatically advances to the
next preset. This function is useful for searching
for a desired TV station in memory.
The above operations are required when a TV
tuner other than TTX7501z is connected.
second or longer to tune in a station.
Watching a video
●Step tuning:
The TV tuner has a VTR input terminal to which
1 external device can be connected. Connect a
12 V video cassette player (VCP) or video
cassette recorder (VCR) to the TV tuner input
terminal.
Press the [a] or [d] button to manually
tune in a station.
1. Press the [P/A] button.
2. When the desired station is found, press the
[P/A] button again to remain tuned to that
station.
Recalling a preset station
A total of 12 TV stations can be stored (6-TV1
and 6-TV2). This allows you to select your
favorite TV stations and store them in memory
for later recall.
1. Press the [
2. To return to the TV broadcast, press the
] button.
] button to select VTR.
Note:
• Do not press and hold the [P/A] button for 2
seconds or longer. Doing so will trigger the auto
store function and start storing stations into
memory.
[
1. Press the [BND] button and select the
Tuning
desired TV band (TV1 or TV2).
There are 3 types of tuning mode available,
Seek tuning, manual tuning and preset tuning.
2. To recall a stored TV station, press the
desired [DIRECT] button to select that
station.
Setting the TV diver
You can change the reception setting for the TV
antenna connected to the TV tuner.
Seek tuning
1. Press the [BND] button and select the
desired TV band (TV1 or TV2).
∗ Press and hold one of the [DIRECT] buttons
for 2 seconds or longer to store the current
station into preset memory.
1. Press and hold the [TITLE] button for 1
second or longer to switch to the adjustment
selection display.
∗ If “MANU” is lit in the display, press and hold
the [BND] button for 1 second or longer.
“MANU” in the display goes off and seek
tuning is now available.
2. Press the [a] or [d] button to select “TV
Manual memory
1. Select the desired station with seek tuning,
manual tuning or preset tuning.
DIVER”.
3. Turn the [ROTARY] knob clockwise to set to
“ON” or counterclockwise to set to “OFF”.
2. Press the [a] or [d] button to
2. Press and hold one of [DIRECT] buttons for
2 seconds or longer to store the current
station into preset memory.
automatically seek a station. Press the [d]
button to automatically tune up the frequency
band to the next available TV station; press
the [a] button to automatically tune down.
● ON:
Sets reception emphasizing the visual.
● OFF:
Sets the diver setting to OFF.
4. Press the [TITLE] button to return to the
previous mode.
22
DXZ435
DXZ435
23
9. IN CASE OF DIFFICULTY
10. ERROR DISPLAYS
If an error occurs, one of the following displays is displayed.
Take the measures described below to eliminate the problem.
Problem
Cause
Fuse is blown.
Measure
Power does not turn
on.
(No sound is pro-
duced.)
Replace with a fuse of the same amperage. If
the fuse blows again, consult your store of
purchase.
Error Display
ERROR 2
Cause
Measure
Incorrect wiring.
Consult your store of purchase.
A CD is caught inside the CD deck and is
not ejected.
This is a failure of CD deck’s mechanism and
consult your store of purchase.
No sound output
Power antenna lead is shor- 1. Turn the unit off.
ted to ground or excessive 2. Remove all wires attached to the power
ERROR 3
ERROR 6
ERROR 2
ERROR 3
ERROR 6
ERROR H
A CD cannot be played due to scratches,
etc.
Replace with a non-scratched, non-warped-
disc.
when operating the
unit with amplifiers or current is required for re-
power antenna at-
tached.
antenna lead. Check each wire for a possible
short to ground using an ohm meter.
3. Turn the unit back on.
mote-on the amplifiers or
power antenna.
A CD is loaded upside-down inside the CD
deck and does not play.
Eject the disc then reload it properly.
4. Reconnect each amplifier remote wire to the
power antenna lead one by one. If the
amplifiers turn off before all wires are
attached, use an external relay to provide
remote-on voltage (excessive current
required).
A CD inside the CD changer is not loaded.
This is a failure of CD changer’s mechanism
and consult your store of purchase.
A CD inside the CD changer cannot be
played due to scratches, etc.
Replace with a non-scratched, non-warped
disc.
Nothing happens
when buttons are
pressed.
The microprocessor has
Turn off the power, then
malfunctioned due to noise, press the [RELEASE]
etc.
button and remove the
DCP.
A CD inside the CD changer cannot be
played because it is loaded upside-down.
Eject the disc then reload it properly.
Display is not accu-
rate.
Press the reset button for
about 2 seconds with a
thin rod.
Displayed when the temperature in the MD
changer is too high and playback has been
stopped automatically.
Lower the surrounding temperature and wait
for a while to cool off MD changer.
Reset button
ERROR 2
ERROR 3
ERROR 6
An MD inside the MD changer is not loaded. This is a failure of MD changer’s mechanism
and consult your store of purchase.
DCP or main unit connec-
tors are dirty.
Wipe the dirt off with a soft cloth moistened with
cleaning alcohol.
An MD inside the MD changer cannot be
played due to scratches, etc.
Replace with a non-scratched, non-warped
disc.
Compact disc cannot Another compact disc is al- Eject the compact disc before loading the new
be loaded.
ready loaded.
one.
An MD inside the MD changer cannot be
played because it is loaded upside-down.
Eject the disc then reload it properly.
Sound skips or is noi- Compact disc is dirty.
sy.
Clean the compact disc with a soft cloth.
Compact disc is heavily
scratched or warped.
Replace with a compact disc with no scratches.
Displayed when a non-recorded MD is
loaded in the MD changer.
Load a pre-recorded MD in the MD changer.
Sound is bad directly Water droplets may form on Let dry for about 1 hour with the power on.
after power is turned the internal lens when the
ERROR 2
ERROR 3
ERROR 6
A DISC inside the DVD changer cannot be
played.
This is a failure of DVD mechanism and
consult your store of purchase.
on.
car is parked in a humid
place.
A DISC cannot be played due to scratches,
etc.
Retry or replace with a non-scratched, non-
warped-disc.
A DISC inside the DVD changer cannot be
played because it is loaded upside-down.
Eject the disc then reload it properly
Set the correct Parental level.
ERROR P
ERROR R
Parental level error
Region code error
Eject the disc and replace correct region
code disc.
If an error display other than the ones described above appears, press the reset button. If the problem
persists, turn off the power and consult your store of purchase.
24
DXZ435
DXZ435
25
11. SPECIFICATIONS
FM Tuner
Frequency Range:
Audio
Maximum Power Output:
87.0 MHz to 108 MHz
208 W (52 W ✕ 4 ch)
Usable Sensitivity:
9 dBf
Continuous Average Power Output:
17 W ✕ 4, into 4 Ω, 20 Hz to 20 kHz, 1%THD
50dB Quieting Sensitivity:
15 dBf
Bass Control Action (60 Hz):
15 dB
Alternate Channel Selectivity:
70 dB
Treble Control Action (10 kHz):
12 dB
Stereo Separation (1 kHz):
35 dB
Line Output Level (CD 1 kHz):
2 V
Frequency Response ( 3 dB):
30 Hz to 15 kHz
General
Power Supply Voltage:
AM Tuner
Frequency Range:
14.4 V DC (10.8 to 15.6 V allowable), negative
ground
531 kHz to 1602 kHz
Current Consumption:
Less than 15 A
Usable Sensitivity:
25 µV
Speaker Impedance:
4 Ω (4 Ω to 8 Ω allowable)
CD Player
System:
Weight / Source unit:
2.64 lb. (1.2 kg)
Compact disc digital audio system
Weight / Remote control unit:
1 oz. (30 g) (including battery)
Usable Discs:
Compact disc
Dimensions / Source unit:
7" (Width) ✕ 2" (Height) ✕ 6-1/8" (Depth)
[178 (W) ✕ 50 (H) ✕ 155 (D) mm]
Frequency Response ( 1 dB):
10 Hz to 20 kHz
Dimensions / Remote control unit:
1-3/4" (Width) ✕ 4-5/16" (Height) ✕ 1-1/8"
(Depth)
Signal to Noise Ratio (1 kHz):
100 dB
Dynamic Range (1 kHz):
95 dB
[44 (W) ✕ 110 (H) ✕ 27 (D) mm]
Harmonic Distortion:
0.01%
Note:
• Specifications and design are subject to change without notice for further improvement.
26
DXZ435
|