User Guide
Bluetooth Handsfree
Car Kit
MODEL:HB600
Table of Contents
Thank you
Thank You
3
3
6
5
7
7
Thank you for purchasing the Hisense HB600 Bluetooth®
Speaker. We hope you enjoy it! This instruction manual will
get you started and ready to make the most of your speaker.
Safety Guidelines
Introducing the HB600
What Your Speaker can do
Specifications
WARNING!
charging Your Speaker
Speakers are capable of delivering sounds at loud volumes
and high pitched tones. Exposure to such sounds can
result in permanent hearing loss damage. The volume
level may vary based on conditions such as the phone
you are using, its reception and volume settings, and the
environment. Please read the safety guidelines below
prior to using this speaker.
GETTING STARTEd
Pairing with Your Phone
8
9-10
How to
Answer a call
End a call
Make a call
Reject a call*
Activate Voice dialing*
Redial Last Number*
Adjust Sound and Volume
call Waiting and Placing a call on Hold*
Reject call Waiting
Mute Function
10
10
10
10
11
11
11
11
11
11
Safety Guidelines
Prior to using this product follow these steps:
1. Before using the speakerphone, turn the volume
control to its lowest level, use the speakerphone
in conversation, and then slowly adjust the volume
control to a comfortable level.
call Transfer From The Speaker
To Mobile Phone
11-12
2. during the use of this product:
What the Lights Mean
Restore Factory Settings
Taking care of Your Speaker
Glossary
13
14
15
Keep the volume at the lowest level possible and
avoid using the speakerphone in noisy environments
where you may be inclined to turn up the volume;
If increased volume is necessary, adjust the volume
control slowly; and if you experience any discomfort
15-16
2
3
WARNING!
or ringing in your ears, immediately discontinue
using the speakerphone and consult a physician.
With continued use at high volume, your ears may
become accustomed to the sound level, which may
result in permanent damage to your hearing without
any noticeable discomfort.
Keep out of reach of children: The plastic bags the product
and its parts are wrapped in are not toys for children. The
bags themselves or the many small parts they contain may
cause choking if ingested.
WARNING!
3. drive Safely
Ignition of flammable atmospheres: do not use the
Speaker in environments where there is a danger of
ignition of flammable gases.
Several studies have shown that cell phone usage
while driving creates a distraction to the driver which
may increase the likelihood of an accident. This
distraction potential is not eliminated by the use
of a handsfree phone. Handsfree phones have not
been shown to be safer than hand-held phones with
respect to driver distraction. When using the phone
while driving, keep conversations short and resist any
temptation to make notes or read documents. Before
answering calls consider your circumstances. Pull off
the road and park before making or answering calls
when driving conditions require (e.g.bad weather,
high traffic density, presence of children in the car,
difficult junctions or maneuvers)
REMEMBER; DRIVING COMES FIRST, NOT THE CALL!
4. Abide by Local Laws.
Please check if the local laws where you live restrict
the use of mobile phones while driving. It is the
owner’s responsibility to use this product in
compliance with the laws of the place where you live.
4
5
What your speaker can do
Introducing the HB600
Your Hisense HB600 lets you do all this
1. Speaker
2. Microphone
3. LEd Light
4. charging Socket
5. Mute Button
6. Multi-Function Button (MFB)
•
•
•
•
•
•
•
•
Answer calls
End calls
Reject calls*
Voice dialing*
Last Number Redialing*
call Waiting*
• Pairing Button – When speaker is turned off press
and hold for 6 sec to put Speaker into pairing mode
• Answer/End Button
Mute conversation
Put call on Hold*
• Press for 4 seconds to turn speaker on (blue lights
flash 5 times)
* Phone dependent
• Press and hold for 5 seconds to turn speaker off
(red light flash 5 times and then power off)
Specifications
7. Volume (+)
8. Volume (-)
•
•
Up to 14 hours talk time/standby time up to 850
hours
Rechargeable battery, with charging option from Ac
power supply and car power outlet.
1
4
5
3
•
•
•
Operating range up to 10 meters (approx. 33 feet)
Headset and hands-free Bluetooth profiles
8
7
Bluetooth specification (see glossary) version
2.1+EdR
6
2
6
7
Charging Your Speaker
Pairing with Your Phone or Other Device
Make sure that your Hisense HB600 speaker is fully charged
before first use (normal charging time is approximately 3
hours). Use the Ac adaptor to charge from a power socket,
or charge directly from you’re your car power outlet using
the charging cable provided After connecting to the power
source, the red LEd will flash while charging.
Before you use your Hisense HB600, you need to pair it
with your mobile phone.
1. Make sure that the HB600 is turned off
2. Press and hold the MFB for 6 sec. until led flash red
and blue alternatively.
3. Activate Bluetooth function of the mobile phone to
search for Bluetooth devices (please refer to the
phone’s manual);
After charging ends the red LEd will turn off.
Auto power off
if the speaker is turned on but not connected to a
Bluetooth device for 15 minutes, the speaker will auto-
matically turn off.
4. Set your Bluetooth phone to ‘discover’ the Hisense
HB600
Follow your phone’s instruction guide. This usually
involves going to a ‘setup,’ ‘connect’ or ‘Bluetooth’
menu on your phone and selecting the option to
‘discover’ or ‘add’ a Bluetooth device.
GETTING STARTED
The Hisense HB600 is easy to operate.
Turning Your Speaker On and Off
To turn your speaker on, press and hold the MFB for 4
seconds. Release the button when you hear short beep, the
blue light will flash 5 times and the speaker will turned on
To turn off your Speaker, press and hold the MFB for 4
seconds. Release the button when you hear short beep,
the blue light will flash 5 times and the speaker will turned
off.
5. Your phone will find the Hisense HB600
8
9
Activate Voice Dialing*
Press the MFB once. Wait for the beep and then an-
nounce the name you wish to call.
For best results, record the voice-dialing tag through your
speaker. Please consult your phone’s user manual for
more information about using this feature.
6. Your phone will then ask if you want to pair with it.
Accept by pressing ‘Yes’ or ‘OK’ on the phone and
confirm with the passkey or PIN = 0000 (4 zeros).
Your phone will confirm when pairing is complete.
In case of unsuccessful pairing, repeat steps 1 to 6.
Redial Last Number*
Press the MFB twice when the speaker is turned on and
not use (StandBy mode).
Note: If the pairing cannot be completed within 2
minutes after the pairing mode is activated, the
speakerphone will power off automatically. Please
repeat steps above to pair the speakerphone and
mobile phone again.
Adjust Sound and Volume
during a call, repeatedly press the Volume (+) or Volume
(-) to change the volume.
Call Waiting and Placing a Call on Hold*
This lets you put a call on hold during a conversation and
answer a waiting call.
Press the MFB twice to put the active call on hold and
answer the waiting call.
How to…
Answer a Call
Press the MFB on your speaker to answer a call.
End a Call
Press the MFB to end an active call.
Press the MFB twice to switch between the two calls.
Tap the MFB to end the active conversation.
Make a Call
Reject Call Waiting
When you make a call from your mobile phone, the call will
(subject to phone settings) automatically transfer to your
speaker. If your phone does not allow this feature, press on
the Hisense HB600’s MFB to transfer the call to the speaker.
during a conversation, Press the MFB for 2 seconds in
order to reject the call waiting.
Mute Function
during a conversation, press the mute button to mute the
microphone.
Reject a Call*
Press the MFB for approximately 2 seconds when the
phone rings to reject an incoming call. depending on your
phone settings, the person who called you will either be
forwarded to your voice mail or hear a busy signal.
To reactivate the microphone, short press the mute button.
10
11
Call Transfer from Speaker to Mobile Phone
Press the volume (+) and volume (-) buttons together. The
conversation will be route to the mobile phone.
What the light means
In order to route the conversation back to the speaker,
press again the volume (+) and volume (-) buttons together
What you see
What does this
mean about your
Speaker
Functions marked with * are dependent on your phone
supporting these features.
check your phone’s user manual for further information.
When
connected
to charger
Solid red LEd
charging
Red LEd turn off
charging
completed
When NOT Red and blue LEd
Pairing
connected flash alternatively.
to charger
Blue LEd flash once
Stand by mode
every 3 seconds
Blue LEd flash twice Stand by mode
every 3 seconds
(but no Bluetooth
device connected
to speaker)
Red LEd flash once
Low power alert
every 3 seconds
Blue LEd flash once
call in progress
every 6 seconds
Red LEd steady on
Mute
Blue LEd flash 5
Power on or off
times rapidly
12
13
Troubleshooting
Taking Care of Your Speaker
I hear crackling noises
For the best audio quality, make sure that the mobile
phone is placed within 10 meter from the speaker.
•
•
Always store the Hisense HB600 with the power off
and safely protected.
Avoid storage at extreme temperatures (above
45°c/113°F – including direct sunlight – or below
-10°c/14°F). This can shorten battery life and may
affect operation. High temperatures may also de-
grade performance.
I cannot hear anything in my speaker
Increase the volume on the mobile phone.
Ensure that the Speaker is paired with the phone.
Make sure that the phone is connected to the speaker –
if it does not connect from the phone’s Bluetooth menu.
•
do not expose the Hisense HB600 to rain or other
liquids.
I have pairing problems even though my phone indicates
otherwise
You may have deleted your speaker pairing connection in
your mobile phone.
Glossary
Follow the pairing instructions in page 9.
Bluetooth
Restore Factory Settings
The Bluetooth® Trademark and logos are owned by the
Bluetooth SIG, Inc. and any use of such marks by Hisense
is under license. Other trademarks and trade names are
those of their respective owners.
In order to restore factory settings and delete all paired
devices from the speaker, while in stand by mode, press
the volume (+) and volume (-) together for 10 seconds,
until the blue LEd flash 5 times. continue pressing for
3 seconds, the speaker will turn off automatically, turn
on the speaker and the speaker will return to its original
settings.
1. Bluetooth is a radio technology that connects
devices, such as mobile phones and speakers,
without wires or cords over a short distance (approx.
Notice: If the speakerphone is connected with a mobile
phone before restore to default setting, it will
enter pairing mode automatically after restored
to default.
2. Bluetooth profiles are the different ways that
Bluetooth devices communicate with other devices.
Bluetooth phones support either headset profile, the
handsfree profile or both. In order to support a certain
14
15
|